欢迎访问恒安机械网站
咨询热线:18653160053
新闻资讯 news
联系我们 CONTACT

地址:济南市槐荫区美里路丽水华庭

电话:18653160053

QQ:850206910

新闻资讯 您当前的位置:首页 - 新闻资讯 >

GMP车间净化公司施工时应使用什么材料

来源:http://www.henganjh.cn │ 发表时间:2019-06-12 

  GMP车间净化公司施工时应使用什么材料
  What materials should be used in the construction of GMP workshop purification company
  目前,GMP洁净车间被广泛应用,我国对设备和材料有严格的规定。到目前为止,生产厂家对洁净车间的设计更加谨慎。今天小编将为您介绍一下,洁净车间选用什么材料合适?
  At present, GMP clean workshop is widely used, China has strict regulations on equipment and materials. So far, manufacturers have been more cautious about the design of clean workshops. Today, Xiaobian will introduce to you what materials are suitable for cleaning workshop.
  洁净车间
  Clean workshop
  1. 清洗车间地面可采用环氧自流地板或高档耐磨塑料地板。如果需要,可以选择防静态类型。
  1. Epoxy self-flow floor or high-grade wear-resistant plastic floor can be used for cleaning workshop floor. If necessary, you can choose the static type.
  2. 进气口采用不锈钢框架,美观干净,冲孔网板采用喷漆铝板,无锈蚀、无粉尘,适合清洗。
  2. High efficiency intake adopts stainless steel frame, beautiful and clean, perforated mesh plate adopts spray-painted aluminium plate, no rust, no dust, suitable for cleaning.
                       GMP车间净化公司
  3.回风管采用热锌板制成,粘贴阻燃PF泡沫塑料板,净化隔热效果好。
  3. The return air duct is made of hot zinc sheet and pasted with flame retardant PF foam plastic sheet. The effect of purification and insulation is good.
  4. 洁净车间墙面及顶板一般采用50mm厚夹芯彩钢板,外观美观,刚性强。圆弧角、门框、窗框等一般采用特殊的氧化铝型材制造。
  4. The wall and roof of clean workshop are generally made of 50mm thick sandwich color steel plate, which has beautiful appearance and strong rigidity. Arc angle, door frame, window frame and so on are generally made of special alumina profiles.
  清洁小窍门:在选材上不要因为成本等原因保守,那不仅达不到净车间的净化效果,而且还影响其使用寿命和资源的浪费。
  Cleaning Tips: Do not be conservative in material selection because of cost and other reasons, which not only can not achieve the purification effect of the clean workshop, but also affect its service life and waste of resources.
  此外,清洁车间照明也很重要
  In addition, clean workshop lighting is also important.
  洁净室是一个大柱网,大跨度,无采光窗封闭的空间。为了不影响视觉效果,提高人员工作效率,有必要对照明有一定的要求。洁净车间的休息厅、走廊、工作室的照明水平不能相差太多,一般控制在1-2级,不小于100 1X。
  Clean room is a large column network, large span, no daylighting window closed space. In order not to affect the visual effect and improve the efficiency of personnel, it is necessary to have certain requirements for lighting. The lighting level of the lounge, corridor and studio in the clean workshop should not be too different. Generally, it should be controlled at level 1-2, not less than 1001X.
  不同洁净车间根据车间照明工艺要求的不同也有很大的差异。如果荧光粉末涂料房间的显像管厂,半导体工厂的光刻的房间,为了防止感光材料,必须使用黄色或红色光源,应满足其特殊需求选择黄色荧光管或低压钠灯,黄色荧光管也有两种,一个是灯的内壁涂黄色荧光粉;另一个是带有黄色塑料套管的白色荧光灯管。
  There are also great differences among different clean workshops according to the requirements of workshop lighting technology. If the picture tube factory of the fluorescent powder coating room and the photolithography room of the semiconductor factory must use yellow or red light source in order to prevent the photosensitive material, the yellow fluorescent tube or low pressure sodium lamp should be selected to meet their special needs. There are two kinds of yellow fluorescent tube, one is the yellow fluorescent powder coated on the inner wall of the lamp; the other is the white fluorescent lamp tube with yellow plastic sleeve.

上一篇:山东无尘车间干净度的测试办法
下一篇:山东无尘车间的装修要求是什么?

鲁公网安备 37010502001103号